- 您现在的位置：买卖IC网 > Sheet目录473 > MAX2839EVKIT+ (Maxim Integrated)KIT EVAL FOR MAX2839
2.3GHz to 2.7GHz MIMO Wireless Broadband
RF Transceiver
AC ELECTRICAL CHARACTERISTICS TABLE—Rx MODE (continued)
(MAX2839 Evaluation Kit, V CC_ = 2.8V, T A = +25°C, f RF = 2.4999GHz, f LO = 2.5GHz; baseband output signal frequency = 100kHz,
f REF = 40MHz, ENABLE = RXTX = CS = high, SCLK = DIN = low, with power matching for the differential RF pins using the typical
applications circuit and registers set to default settings and corresponding test mode, unless otherwise noted. Lowpass filter is set to
10MHz RF channel BW. Unmodulated single tone RF input signal is used with specifications which normally apply over the entire
operating conditions, unless otherwise indicated.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Out-of-Band Input IP3 (Note 2)
AGC set for -65dBm wanted signal, max RF gain
(B7:B6 = 00)
AGC set for -55dBm wanted signal, max RF gain - 8dB
(B7:B6 = 01)
AGC set for -40dBm wanted signal, max RF gain - 16dB
(B7:B6 = 10)
AGC set for -30dBm wanted signal, max RF gain - 32dB
(B7:B6 = 11)
Max RF gain (B7:B6 = 00)
-13
-9
-7
+16
-37
dBm
Inband Input P-1dB
Maximum Output Signal Level
I/Q Gain Imbalance
I/Q Phase Error
Rx I/Q Output Load Impedance
(R || C)
Max RF gain - 8dB (B7:B6 = 01)
Max RF gain - 16dB (B7:B6 = 01)
Max RF gain - 32dB (B7:B6 = 11)
Over passband frequency range; at any gain setting;
1dB compression point
100kHz IQ baseband output; 1 σ variation
100kHz IQ baseband output; 1 σ variation
Minimum differential resistance
Maximum differential capacitance
10
-29
-21
-4
1.5
0.1
0.125
5
dBm
V P-P
dB
Degrees
k Ω
pF
Loopback Gain (for Receiver I/Q
Calibration)
Transmitter I/Q input to receiver I/Q output; transmitter
B6:B1 = 000011, receiver B5:B0 = 101000 programmed
through SPI
-5
0
+5
dB
After switching RXHP to 0; average over 1μs after any
I/Q Output DC Droop
gain change, or 2μs after receive enabled with 100Hz
1
V/s
AC-coupling
I/Q Static DC Offset
Isolation Between Rx Channels A
and B
No RF input signal; measure at 3μs after receive enable;
RXHP = 1 for 0 to 2μs and set to 0 after 2μs, 1 σ variation
Any RF gain settings
2
40
mV
dB
RECEIVER BASEBAND FILTERS
At 15MHz
57
Baseband Filter Rejection
At 20MHz
At > 40MHz
RXHP = 1 (used before AGC completion)
D5:D4 = 00
75
90
650
0.1
dB
Baseband Highpass Filter Corner
Frequency
RXHP = 0 (used after AGC
completion) address A4:A0 = 01110
D5:D4 = 01
D5:D4 = 10
1
30
kHz
D5:D4 = 11
100
4
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX2851ITK+
TRANSMITTER MIMO 5GHZ 5CH 68TQFN
MAX2852ITK+
IC RECEIVER DFS 5GHZ 68TQFN
MAX2870EVKIT#
EVAL KIT MAX2870
MAX2904EVKIT
EVAL KIT
MAX3524EVKIT
EVAL KIT MAX3524
MAX3540EVKIT#
KIT FOR MAX3540 DVB TUNER
MAX3541EVKIT+
KIT FOR MAX3541 DVB TUNER
MAX3542CLM+
IC TV TUNER SGL CONV 48LFCGA
相关代理商/技术参数
MAX283X-RD0089
制造商:Maxim Integrated Products 功能描述:INTERFACE BOARD - Bulk
MAX2842ETN+
制造商:Maxim Integrated Products 功能描述:3.3-3.9GHZ MIMO WIMAX RF TRANSCEIVER - Rail/Tube
MAX2842ETN+T
制造商:Maxim Integrated Products 功能描述:3.3-3.9GHZ MIMO WIMAX RF TRANSCEIVER - Tape and Reel
MAX2850EVKIT+
制造商:Maxim Integrated Products 功能描述:EVKIT FOR MAX2850 - Boxed Product (Development Kits)
MAX2850ITK+
功能描述:射频发射器 5GHZ 4Ch MIMO Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
MAX2850ITK+T
功能描述:射频发射器 5GHZ 4Ch MIMO Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
MAX2851ITK+
功能描述:射频接收器 RF and RFID 射频接收器s - TRANSMITTER MIMO 5GHZ 5CH 68TQFN RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX2851ITK+T
功能描述:射频接收器 RF and RFID 射频接收器s - TRANSMITTER MIMO 5GHZ 5CH 68TQFN RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel